Brand: Sharp
Models: 20U250 universe
Symptoms: Protec, 6x blinking red light
Cause: PLN voltage spanning, C612 100mf / 160v swell resulting in data errors
Solution: replace ic eeprom 24c08
Brand: Sharp
Model: 29ZF250S
Symptoms: vertical defect image
Cause: ic vertical 24v voltage drops
Solution: R501 0,22ohm delay value, replace R o, 22ohm / 2w
Brand: Sharp
Model: piccolo
Symptoms: smaller image top and bottom
Cause: resistor between playback which broke up into vertical ic
Solution: replace with the same value, what if there is no change in the vertical ic replace with new-
Note: Elco also check that there is no possibility in the vertical weak
Brand: Sharp
Model: 14X20D2
Symptoms: every 5mn or more die alone / total, if it is turned off from the switch on / off and then turned on the tv back to normal again.
Cause: STR regulator defect
Solution: replace a new one immediately dg dg same type.
Tools: Monitor
Devices: TV
Brand: Sharp
Models: 20U250 universe
Symptoms: Protec, 6x blinking red light
Cause: PLN voltage spanning, C612 100mf / 160v swell resulting in data errors
Solution: replace ic eeprom 24c08
Devices: TV
Brand: Sharp
Model: 29ZF250S
Symptoms: vertical defect image
Cause: ic vertical 24v voltage drops
Solution: R501 0,22ohm delay value, replace R o, 22ohm / 2w
Devices: TV
Brand: Sharp
Model: piccolo
Symptoms: smaller image top and bottom
Cause: resistor between playback which broke up into vertical ic
Solution: replace with the same value, what if there is no change in the vertical ic replace with new-
Note: Elco also check that there is no possibility in the vertical weak
Devices: TV
Brand: Sharp
Model: 14X20D2
Symptoms: every 5mn or more die alone / total, if it is turned off from the switch on / off and then turned on the tv back to normal again.
Cause: STR regulator defect
Solution: replace a new one immediately dg dg same type.
Devices: TV
Brand: Sharp
Model: 51V20MS
Symptoms: i turn around a few minutes later dead total.Lampu standby LED is not lit at all
Cause: This indicates that the circuit swtching (SMPS) does not work after using STR panas.smps w6753
Solution: str w6753 new-dng replace if necessary .. plus another heatsink
Devices: TV
Brand: Sharp
Model: SHARP C14JO
Symptoms: SMALL PICTURE few centimeters Amid ONLY
Cause: TRANSISTOR BROKEN
Solutions: CHANGE Q604
Devices: TV
Brand: Sharp
Model: Alexander
Symptoms: image narrows
Cause: depleksi short
Solution: replace the deflection
Devices: TV
Brand: Sharp
Model: 14Q25MKLL
Symptoms: total dead
Cause: The regulator is less well
Solution: G5653 STR nice if ill drop out fuse check its value R707 470k mdah damaged usual ...
Devices: TV
Brand: Sharp
Model: 29DXS250E
Symptoms: total dead
Cause: fly back short causing high load so psu protect
Solution: replace the FBT with new-
Devices: TV
Brand: Sharp
Model: UA-1 chassis
Symptoms: Raster dark, entering service mode ok, exit service mode dark again.
Cause: Data eprom change.
Solution: change the data service mode EVG from 1 to 0 and EHT from 1 to 0
Note: chassis models UA-1 universe and wonder
Devices: TV
Brand: Sharp
Model: 51X220 EXPRESSION
Symptoms: Shown without PICTURE WITH SOUND HIDUP.KADANG POSITION BACK TO STANDBY (Protek)
Cause: unknown morbidly
Solution: R GUIDES FOR 180V CHANGE R621: 1 OHM
Devices: TV
Brand: Sharp
Model: C14JO
Symptoms: SMALL PICTURE few centimeters Amid SAJA.RASTER JUST EMPTY / BINTIK.KESALAHAN OCCURS ON LINE 12V
Cause: unknown morbidly
Solution: Q604 FOR CHANGE ration 12volt D ALSO TO GET TUNER.
Devices: TV
Brand: Sharp
Model: Qbeit 11
Symptoms: no release Raster cut no
Cause: hit by lightning
Solution: lightning hit damage after check everything turned his IC died after learning scheme
Note: for all what peer 2 ic sharp when stock runs out the use of IC 1XC 927WJZZQ CHANGE AJ Pake IC IXC 844WJZZ.selamat try
Devices: TV
Brand: Sharp
Model: piccolo
Symptoms: total dead
Cause: The total death
Solution: First check the regulator str outputnya.terus to replace the lamp voltage setandar.jika stnby can not issue the check flame ic program.
Note: if ic program (R2J1Q172GA-A00FP) do not try to use ic flame. {1X245 WJN] jadi.ta Thank God there is a problem.
Devices: TV
Brand: Sharp
Model: Alexander 21inch
Symptoms: Indicators sbntar truz flame die. . .
Cause: Protek Regulator
Solution: Replace fet SE 125
Devices: TV
Brand: Sharp
Model: X-pression 51X200
Symptoms: Sounds normal, ill be FOCUS Picture
Causes: Leg focus on crt half short.
Solution: Figure ill be the focus not coming from the flyback or CRT socket and glue gagal.plastik was already cleared of foot crt, focus primarily on the feet.
Note: After the test to another crt, great picture quality is perfect! Crt DNG such cases if the damage from its flyback failed. ooh .. sharp
Devices: TV
Brand: Sharp
Model: 51X200 Xpression
Symptom: Picture v hold / cliches
Cause: C 434 10 / 50V err measured 3.3 uf
Solution: Replace with good
Devices: TV
Brand: Sharp
Model: fdfde
Symptoms: total dead
Cause: short horizontal transistors
Solution: Change Transistors
Devices: TV
Brand: Sharp
Model: wonder
Symptoms: There rgb color line, n re-standby
Cause: r33ohm that the voltage fuse to burn Vertical Ic
Solution: replace r33ohm, and Ic Vertical
Note: vertical ic replacement, if indeed r 33terasa hot sangt
Devices: TV
Brand: Sharp
Models: 20U200
Symptoms: Voice gresek-gresek, nice pictures, sound system locked on D / K and can not be replaced
Cause: The change and adjust, eprom 24C08
Solution: replace and adjust, eprom 24C08
Devices: TV
Brand: Sharp
Model: 51R200
Symptoms: In the star live and die, so the red LED
Cause: R502 check for voltage Vertical Gati if necessary
Solution: check for voltage Vertical R502 Gati if necessary
Devices: TV
Brand: Sharp
Model: 14W25
Symptoms: live tv for a while continue to STBY.
Cause: Protec of ABL
Solution: R604,39k putus.ganti tv turns back to normal.
Devices: TV
Brand: Sharp
Model: 20X20
Symptoms: total dead, when the power button is pressed the indicator light's his red, then green, then back again to red
Cause: solder off.
Solution: re-solder, IC EEPROM should be reset IC, the way is when the TV is off, Jumper J137 to J138. After that turn on the TV, while for IC EEPROM Let wiriting TV turns back to normal, then turn off the TV, then remove the jumper before.
Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: Protek green light keeps red
Cause: 180k resistor open
Solution: replace the 180k resistor near abl pathways
Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: dark picture of normal voice
Cause: 33k resistor open
Solution: replace the 33k resistor on track afc
Devices: TV
Brand: Sharp
Model: sharp Universe
Symptoms: normal image-lived briefly dead
Cause: capacitor 104 open
Solution: replace the capacitor ic 104 near croma
Devices: TV
Brand: Sharp
Model: wonder
Symptoms: regulator 6654 kerja.strf not okay
Cause: r 680k / 560k putuss
Solution: replace r TSB
Devices: TV
Brand: Sharp
Model: 21 wonder
Symptoms: Lapu blink 6 times (Protek)
Cause: Memory IC c2416
Solution: replace the IC c2416 enter Service mode turn off the TV set Vertical straight line okay
Note: See Jemper to enter service mode
Devices: TV
Brand: Sharp
Model: flat screen
Symptoms: stanbay
Cause: vol 5 no
Solution: replace the stable
Devices: TV
Brand: Sharp
Model: univers
Symptom: on a moment ago Protek
Cause: ic vertical dead
Solution: gani ic
Devices: TV
Brand: Sharp
Model: slhim
Symptoms: vertical roll
Cause: The yoke broke
Solution: loading and then continued ,,,, jreng deh
Devices: TV
Brand: Sharp
Model: UNIVERSE 20u200
Symptom: LEDs blink alternately RED GREEN RESISTANCE
Cause: Damaged IC voltage
Solution: check his eprrom
Devices: TV
Brand: Sharp
Model: SHARP 51X220
Symptoms: Shown without PICTURE WITH SOUND POSITION ON
Cause: The power supply voltage
Solution: R GUIDES FOR 180V CHANGE R621: 1 OHM
Devices: TV
Brand: Sharp
Model: universe
Symptoms: Protek
Cause: IC momori or cracked solder
Solution: re-solder, replace the IC memory
Devices: TV
Brand: Sharp
Model: 20w200
Symptoms: Protek standby light blinking 7 times
Cause: ic memory error
Solution: replace the memory ic
Models: 20U250 universe
Symptoms: Protec, 6x blinking red light
Cause: PLN voltage spanning, C612 100mf / 160v swell resulting in data errors
Solution: replace ic eeprom 24c08
Brand: Sharp
Model: 29ZF250S
Symptoms: vertical defect image
Cause: ic vertical 24v voltage drops
Solution: R501 0,22ohm delay value, replace R o, 22ohm / 2w
Brand: Sharp
Model: piccolo
Symptoms: smaller image top and bottom
Cause: resistor between playback which broke up into vertical ic
Solution: replace with the same value, what if there is no change in the vertical ic replace with new-
Note: Elco also check that there is no possibility in the vertical weak
Brand: Sharp
Model: 14X20D2
Symptoms: every 5mn or more die alone / total, if it is turned off from the switch on / off and then turned on the tv back to normal again.
Cause: STR regulator defect
Solution: replace a new one immediately dg dg same type.
Tools: Monitor
Devices: TV
Brand: Sharp
Models: 20U250 universe
Symptoms: Protec, 6x blinking red light
Cause: PLN voltage spanning, C612 100mf / 160v swell resulting in data errors
Solution: replace ic eeprom 24c08
Devices: TV
Brand: Sharp
Model: 29ZF250S
Symptoms: vertical defect image
Cause: ic vertical 24v voltage drops
Solution: R501 0,22ohm delay value, replace R o, 22ohm / 2w
Devices: TV
Brand: Sharp
Model: piccolo
Symptoms: smaller image top and bottom
Cause: resistor between playback which broke up into vertical ic
Solution: replace with the same value, what if there is no change in the vertical ic replace with new-
Note: Elco also check that there is no possibility in the vertical weak
Devices: TV
Brand: Sharp
Model: 14X20D2
Symptoms: every 5mn or more die alone / total, if it is turned off from the switch on / off and then turned on the tv back to normal again.
Cause: STR regulator defect
Solution: replace a new one immediately dg dg same type.
Devices: TV
Brand: Sharp
Model: 51V20MS
Symptoms: i turn around a few minutes later dead total.Lampu standby LED is not lit at all
Cause: This indicates that the circuit swtching (SMPS) does not work after using STR panas.smps w6753
Solution: str w6753 new-dng replace if necessary .. plus another heatsink
Devices: TV
Brand: Sharp
Model: SHARP C14JO
Symptoms: SMALL PICTURE few centimeters Amid ONLY
Cause: TRANSISTOR BROKEN
Solutions: CHANGE Q604
Devices: TV
Brand: Sharp
Model: Alexander
Symptoms: image narrows
Cause: depleksi short
Solution: replace the deflection
Devices: TV
Brand: Sharp
Model: 14Q25MKLL
Symptoms: total dead
Cause: The regulator is less well
Solution: G5653 STR nice if ill drop out fuse check its value R707 470k mdah damaged usual ...
Devices: TV
Brand: Sharp
Model: 29DXS250E
Symptoms: total dead
Cause: fly back short causing high load so psu protect
Solution: replace the FBT with new-
Devices: TV
Brand: Sharp
Model: UA-1 chassis
Symptoms: Raster dark, entering service mode ok, exit service mode dark again.
Cause: Data eprom change.
Solution: change the data service mode EVG from 1 to 0 and EHT from 1 to 0
Note: chassis models UA-1 universe and wonder
Devices: TV
Brand: Sharp
Model: 51X220 EXPRESSION
Symptoms: Shown without PICTURE WITH SOUND HIDUP.KADANG POSITION BACK TO STANDBY (Protek)
Cause: unknown morbidly
Solution: R GUIDES FOR 180V CHANGE R621: 1 OHM
Devices: TV
Brand: Sharp
Model: C14JO
Symptoms: SMALL PICTURE few centimeters Amid SAJA.RASTER JUST EMPTY / BINTIK.KESALAHAN OCCURS ON LINE 12V
Cause: unknown morbidly
Solution: Q604 FOR CHANGE ration 12volt D ALSO TO GET TUNER.
Devices: TV
Brand: Sharp
Model: Qbeit 11
Symptoms: no release Raster cut no
Cause: hit by lightning
Solution: lightning hit damage after check everything turned his IC died after learning scheme
Note: for all what peer 2 ic sharp when stock runs out the use of IC 1XC 927WJZZQ CHANGE AJ Pake IC IXC 844WJZZ.selamat try
Devices: TV
Brand: Sharp
Model: piccolo
Symptoms: total dead
Cause: The total death
Solution: First check the regulator str outputnya.terus to replace the lamp voltage setandar.jika stnby can not issue the check flame ic program.
Note: if ic program (R2J1Q172GA-A00FP) do not try to use ic flame. {1X245 WJN] jadi.ta Thank God there is a problem.
Devices: TV
Brand: Sharp
Model: Alexander 21inch
Symptoms: Indicators sbntar truz flame die. . .
Cause: Protek Regulator
Solution: Replace fet SE 125
Devices: TV
Brand: Sharp
Model: X-pression 51X200
Symptoms: Sounds normal, ill be FOCUS Picture
Causes: Leg focus on crt half short.
Solution: Figure ill be the focus not coming from the flyback or CRT socket and glue gagal.plastik was already cleared of foot crt, focus primarily on the feet.
Note: After the test to another crt, great picture quality is perfect! Crt DNG such cases if the damage from its flyback failed. ooh .. sharp
Devices: TV
Brand: Sharp
Model: 51X200 Xpression
Symptom: Picture v hold / cliches
Cause: C 434 10 / 50V err measured 3.3 uf
Solution: Replace with good
Devices: TV
Brand: Sharp
Model: fdfde
Symptoms: total dead
Cause: short horizontal transistors
Solution: Change Transistors
Devices: TV
Brand: Sharp
Model: wonder
Symptoms: There rgb color line, n re-standby
Cause: r33ohm that the voltage fuse to burn Vertical Ic
Solution: replace r33ohm, and Ic Vertical
Note: vertical ic replacement, if indeed r 33terasa hot sangt
Devices: TV
Brand: Sharp
Models: 20U200
Symptoms: Voice gresek-gresek, nice pictures, sound system locked on D / K and can not be replaced
Cause: The change and adjust, eprom 24C08
Solution: replace and adjust, eprom 24C08
Devices: TV
Brand: Sharp
Model: 51R200
Symptoms: In the star live and die, so the red LED
Cause: R502 check for voltage Vertical Gati if necessary
Solution: check for voltage Vertical R502 Gati if necessary
Devices: TV
Brand: Sharp
Model: 14W25
Symptoms: live tv for a while continue to STBY.
Cause: Protec of ABL
Solution: R604,39k putus.ganti tv turns back to normal.
Devices: TV
Brand: Sharp
Model: 20X20
Symptoms: total dead, when the power button is pressed the indicator light's his red, then green, then back again to red
Cause: solder off.
Solution: re-solder, IC EEPROM should be reset IC, the way is when the TV is off, Jumper J137 to J138. After that turn on the TV, while for IC EEPROM Let wiriting TV turns back to normal, then turn off the TV, then remove the jumper before.
Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: Protek green light keeps red
Cause: 180k resistor open
Solution: replace the 180k resistor near abl pathways
Devices: TV
Brand: Sharp
Model: Q vision
Symptoms: dark picture of normal voice
Cause: 33k resistor open
Solution: replace the 33k resistor on track afc
Devices: TV
Brand: Sharp
Model: sharp Universe
Symptoms: normal image-lived briefly dead
Cause: capacitor 104 open
Solution: replace the capacitor ic 104 near croma
Devices: TV
Brand: Sharp
Model: wonder
Symptoms: regulator 6654 kerja.strf not okay
Cause: r 680k / 560k putuss
Solution: replace r TSB
Devices: TV
Brand: Sharp
Model: 21 wonder
Symptoms: Lapu blink 6 times (Protek)
Cause: Memory IC c2416
Solution: replace the IC c2416 enter Service mode turn off the TV set Vertical straight line okay
Note: See Jemper to enter service mode
Devices: TV
Brand: Sharp
Model: flat screen
Symptoms: stanbay
Cause: vol 5 no
Solution: replace the stable
Devices: TV
Brand: Sharp
Model: univers
Symptom: on a moment ago Protek
Cause: ic vertical dead
Solution: gani ic
Devices: TV
Brand: Sharp
Model: slhim
Symptoms: vertical roll
Cause: The yoke broke
Solution: loading and then continued ,,,, jreng deh
Devices: TV
Brand: Sharp
Model: UNIVERSE 20u200
Symptom: LEDs blink alternately RED GREEN RESISTANCE
Cause: Damaged IC voltage
Solution: check his eprrom
Devices: TV
Brand: Sharp
Model: SHARP 51X220
Symptoms: Shown without PICTURE WITH SOUND POSITION ON
Cause: The power supply voltage
Solution: R GUIDES FOR 180V CHANGE R621: 1 OHM
Devices: TV
Brand: Sharp
Model: universe
Symptoms: Protek
Cause: IC momori or cracked solder
Solution: re-solder, replace the IC memory
Devices: TV
Brand: Sharp
Model: 20w200
Symptoms: Protek standby light blinking 7 times
Cause: ic memory error
Solution: replace the memory ic
Post a Comment for "how to sharp problem tv"